HONGYANG GROUP Ecuador Technical Center

Fax: +86 (577)88097280

HONGYANG Group logo

HONGYANG GROUP Ecuador Technical Center , Discuss Technical Problem , Suply After Service Online of Fuel Dispenser, Please Regist Firstly

U206 Micro-switch

fuel-dispenser

U206 Micro-switch

Features:

Water-proof design

Inflaming retarding cable

Weight:170g

100% Factory Tested.

products links

links

technical archives

    but also container, vacuum pump. The hose made according to GB10543 consists of inner rubber lay fuel dispenser er, enhancing layer, conductible metal line and ext fuel dispenser erior rubber layer. Whichever hose abided by the requirements of GB/T9081-2001 Fuel dispenser for vehicle and JJG443-98 Fuel Dispenser in terms of safety and accuracy. During operation pay much attention to protect hose: avoid as much crook as possible; prevent pressure on hose; avoid and reduce abrasion with ground. 4. Connection and seal about pipeline and hydraulic elements Each part of fuel dispenser adopts pipeline connection, dividing into hard type and soft type. In hard type connection steel pipe, brass pipe and aluminum pipe are adopted as pipeline, but in soft type one hose and corrugated pipe. Connected components includes relative elbow jointer, flange and directive jointer. There are following seal types: cone-shaped seal, subulate thread seal, O-ring seal, rubber and asbestos gasket, cork and rubber board, engineering rubber board. According to regulation stipulated in GB/T9081 every fuel dispenser should be conducted sealability testing before leaving factory, no leakage found under normal operation. As replace some parts or found leakage these problems should be paid attention: Cone-shaped seal structure Cone-shaped seal structure also called as expanding jointer, which is composed of pipe with outstretched end, flat spout and outside thread bushing. Sealability is ensured through tightly integration of subulate surfaces. In disassembling or reassembling cone-shaped seal structure pays much attention not to hurt or broken sublatae surfaces, cleaning waste. Thread airproof As disconnection or reassembly thread surface should be kept clean, daubing seal glue or seal belt before installation. O-ring seal Most manufacturers adopts national standard to design O-ring seal, reaching a good sealability. However, some parts is impossible to adopt national standards because of specific structure. Thus, user should purchase or employ appropri fuel dispenser

technical specification

    o the IFSF Dispenser  Application.  Please note that a PCDs may also control devices other than fuel dispenser dispensers.   123.4   Pr fuel dispenser oprietary Pump Protocol Site Controller   IFSF Dispenser Protocol   Protocols   Converter (Control Device)   Device   123.4   Proprietary Pump   Protocols  The PCD may have a one to one relationship with a dispenserpump or may be capable of  controlling several dispensers. In some circumstances the PCD may actually reside physically  in the dispenser. It is also foreseen that more than one PCD may be connected to the SCCD.  The task that a PCD has to accomplish is to successfully make the SCCD believe that it is  communicating directly with a fully IFSF compatible device.  6.2 Configuration of the PCD  The PCD can not expect to receive configuration from the IFSF SCCD as the SCCD will not  have all the required configuration information required for a device controlling different types  of dispenserpumps. Hence the PCD supplier will have to provide the means of configuring  their device separately.  Some PCD Parameters that will not be known by the IFSF SCCD are:   Link between Proprietary device address and the IFSF logical (LNA) address.   Proprietary protocol used by the proprietary devices.   Default values for varies IFSF and non IFSF parameters.   Etc.  6.3 Device Addressing  FP31_2.23 IFSF - STANDARD FORECOURT PROTOCOL March 2006   DISPENSER APPLICATION   Page: 138  The PCD may be controlling more than one proprietary dispenser. Hence there is fuel dispenser

we are committed to create the best workplace, encourage our staffs to put their own personalities into their jobs, and provide them a stage to show themselves.

    er to let those who deny well-documented facts expose themselves to ridicule than pose as martyrs. fuel dispenser But the Muhammad cartoons were lawful in all the fuel dispenser European countries where they were published. And when western newspapers lawfully publish words or pictures that cause offence—be they ever so unnecessary, insensitive or disrespectful—western governments should think very carefully before denouncing them. Freedom of expression, including the freedom to poke fun at religion, is not just a hard-won human right but the defining freedom of liberal societies. When such a freedom comes under threat of violence, the job of governments should be to defend it without reservation. To their credit, many politicians in continental Europe have done just that. France s interior minister, Nicolas Sarkozy, said rather magnificently that he preferred “an excess of caricature to an excess of censorship”—though President Jacques Chirac later spoiled the effect by condemning the cartoons as a “manifest provocation? Shouldn t the right to free speech be tempered by a sense of responsibility? Of course. Most people do not go about insulting their fellows just because they have a right to. The media ought to show special sensitivity when the things they say might stir up hatred or hurt the feelings of vulnerable minorities. But sensitivity cannot always ordain silence. Protecting free expression will often require hurting the feelings of individuals or groups, even if this damages social harmony. The Muhammad cartoons may be such a case. In Britain and America, few newspapers feel that their freedoms are at risk. But on the European mainland, some of the papers that published the cartoons say they did so precisely because their right to publish was being called into question. In the Netherlands two years ago a film maker was murdered for daring to criticise Islam. Danish journalists have received death threats. In a climate in which political correctness has morphed into fear of physical attack, fuel dispenser